Showing 242 results
for
"cutting car"
MTB-CUT 180T
"This video provides a step-by-step guide on how to repair the cutting Car.
Please note:
When reinstalling the Car, pay close attention to the clearance between the Car and the gu...
MTB-CUT 180T
"The machine is equipped with X-axis and Y-axis motors. The X-axis motor is responsible for controlling the horizontal (left-right) movement of the cutting Car.
If the X-axis belt...
MTB-CUT 180T
"Loosening of the car from the guide rail is one of the main causes of cutting distortion.
If such an issue occurs, it is necessary to adjust the clearance between the car and the...
MTB-CUT 180T
"If the cutting Car fails to stop properly when reaching the edge and produces a loud noise, it is likely due to an error in the Car’s limit positioning.
You can replace specific p...
MTB-CUT 180T
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT M288
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT 180T
Please first confirm the specific issue you are facing:
1. If the blade holder does not go down during cutting
This is usually caused by a mainboard malfunction.
In this case, t...
MTB-CUT M188
"If the cutting Car does not stop automatically when it moves to either side and produces a loud noise, it may be due to a malfunctioning limit switch, which prevents the cutting C...
MTB-CUT 180T
"Here is a video on how to replace the cutting car.
https://osscdn.mietubl.com/video/202508141609.mp4"
MTB-CUT 180T
"If the Car moves after you initiate cutting, but the blade holder does not drop, this issue may be caused by one of the following reasons:
Insufficient power supply – Please verif...
MTB-CUT M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT 180T
This issue is usually caused by the fixing screws at the back of the machine that secure the carriage during shipping not being removed.
Please check if the fixing screws at the b...
MTB-CUT 180T
When you first receive the machine, you must remove the transport-locking screw located on the back of the device to prevent damage to the blade carriage.
During normal daily us...
MTB-CUT 180T
"When cutting back films, you need to consider both the pattern position and the cutting range. You can adjust these by setting the material size and enabling or disabling center c...
MTB-CUT 180T
The cutting speed does not have a major impact on most cutting tasks.
In general:
👉 200 is the recommended default cutting speed.
You only need to reduce the cutting speed when...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size main...
MTB-CUT 180T
Center Cutting is a function that positions the cutting area exactly in the center of the material.
The cutting position is calculated based on the width and height values you ent...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size mainl...
MTB-CUT 180T
This issue is usually caused by a mismatch between the material size settings and the template being used.
When cutting full back film, the cutting area is larger than standard te...
Showing 1
to 20
of 242 results
