Showing 49 results
for
"blade holder"
MTB-CUT 180T
"Here are some default setting ：material size is 180mm width × 120mm height.
Cutting pressure: 300
Cutting speed: 200
Blade holder scale: 5
These default settings are sui...
MTB-CUT 180T
"This can be caused by several issues:
- Incorrect Power Supply: Ensure you are using the original power adapter. An incorrect adapter can cause insufficient power.
- Blade Pressu...
MTB-CUT 180T Pro
The Blade Holder Scale depends on the thickness of the material.
For most TPU screen protector materials, the following settings are recommended:
Blade Size: 5
Pressure: 300
&n...
MTB-CUT 180T Pro
The Blade Holder Scale depends on the thickness of the material.
For most Back Film materials, the recommended settings are:
Blade Size: 4
Pressure: 300
These settings...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
Under normal conditions, we recommend replacing the blade after approximately: 300 cuts
However, this is only a recommended value.
The actual blade lifespan may increase or decre...
MTB-CUT 180T
If the blade does not drop properly during cutting, this issue is most likely caused by a mainboard malfunction.
The blade-down action is controlled by the Y-axis motor signal fro...
MTB-CUT 180T
"The rubber cutting mat strip located beneath the blade serves to prevent blade wear and extend the blade’s service life.
However, after prolonged use, the surface of the mat strip...
MTB-CUT 180T
When you first receive the machine, you must remove the transport-locking screw located on the back of the device to prevent damage to the blade carriage.
During normal daily us...
MTB-CUT 180T
"The default parameters of the screen protector cutting machine — blade holder scale 5 and cutting pressure 300g — are suitable for most materials, including HD clear film.
If the...
MTB-CUT 180T
"The recommended cutting parameters for UV materials on the screen protector cutting machine are:
Blade holder scale: 6, Cutting pressure: 380.
If the machine cannot cut properl...
MTB-CUT 180T
"If the machine is unable to cut screen protector materials properly, please first try the following steps:
Replace the blade and blade holder with new ones.
Set the cutting pre...
MTB-CUT 180T
It is generally recommended to replace the blade after around 300 cuts.
The actual replacement frequency may vary depending on material type and usage. If cutting quality...
MTB-CUT 180T
The correct cutting parameters depend on the materials being used. Here are some recommended settings for common materials:
Material | Back Film | Four Layer Soft Film | Explosion-...
MTB-CUT 180T
This issue is usually caused by the rollers not gripping the material properly, allowing it to shift during cutting.
Please check the following:
Ensure all rollers are positioned...
MTB-CUT 180T
If you encounter problems while configuring the machine, you can try using the following default settings, which work for most materials:
Recommended Default Settings
Speed: 20...
MTB-CUT 180T
"The recommended cutting parameters for back films are:
Material Size: 180mm width × 120mm height
Pressure: 300
Blade Holder Scale: 5
Speed: 200
These settings are suit...
MTB-CUT 180T
If the circle cut is not perfect, the issue is usually caused by a loose cutting carriage, which makes the cutting path unstable and results in an imperfect circle.
Please follo...
MTB-CUT 180T
Installing a UV screen protector is different from applying regular screen protector materials.
UV protectors require an additional curing step to harden the surface.
Steps &...
MTB-CUT 180T
In most cases, it is recommended to keep the cutting speed at the default value of 200.
This setting is suitable for most cutting materials.
The recommended blade pressure is: 30...
Showing 21
to 40
of 49 results
