Showing 85 results
for
"default settings"
MTB-CUT 180T
"You can set the Cutter App as the default startup app by following these steps:
Open the device System Settings.
Locate Cutter App (usually found under App Management or Defaul...
MTB-CUT 180T
If you encounter problems while configuring the machine, you can try using the following default settings, which work for most materials:
Recommended Default Settings
Speed: 20...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size main...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size mainl...
MTB-CUT 180T
"Here are some default setting ：material size is 180mm width × 120mm height.
Cutting pressure: 300
Cutting speed: 200
Blade holder scale: 5
These default settings are sui...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size main...
MTB-CUT 180T
The Gear Ratio controls the relationship between motor movement and the actual cutting distance. It is a key parameter that directly affects cutting accuracy and scaling.
The defa...
MTB-CUT 180T
"The default cutting speed of the machine is 200. In most cases, keeping the default setting will deliver good cutting performance.
You only need to reduce the speed in special sit...
MTB-CUT 180T
"If you start the screen protector cutting machine but the Cutter app does not launch automatically, this may be because the device was recently reset and the Cutter app has not be...
MTB-CUT 180T
The blade size (blade holder scale) should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade size, while thi...
MTB-CUT 180T Pro
Please keep speed at 200.
The blade holder scale should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade s...
MTB-CUT 180T
If the machine is operating slowly, it is usually because the cutting speed is set too low.
You can adjust the setting by following these steps:
Open the Settings page;
Find the...
MTB-CUT 180T
"The default parameters of the screen protector cutting machine — blade holder scale 5 and cutting pressure 300g — are suitable for most materials, including HD clear film.
If the...
MTB-CUT 180T
"The cutting machine may work slowly if the cutting speed setting is too low.
Please try setting the cutting speed to the default value of 200 and then attempt cutting again.
If...
MTB-CUT 180T
This issue is usually caused by a mismatch between the material size settings and the template being used.
When cutting full back film, the cutting area is larger than standard te...
MTB-CUT 180T
The blade size (blade holder scale) should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade size, while thi...
MTB-CUT 180T
This issue is usually caused by a mismatch between the material size settings and the template being used.
When cutting full back film, the cutting area is larger than standard te...
MTB-CUT 180T
In most cases, you can keep the cutting speed at the default value of 200.
This setting works well for the majority of materials.
When to reduce the speed
You should lower the...
MTB-CUT 180T
The material size setting depends on the actual material you are using.
By default, the machine is set to:
180 mm (width) × 120 mm (height)
Please pay attention to the o...
MTB-CUT 180T
"The version test password feature is intended only for limited testing before a new version is officially released.
It does not always take effect, and the default password is usu...
Showing 1
to 20
of 85 results
