Showing 78 results
for
"material preparation"
MTB-CUT 180T
"If the tablet screen protector is not cutting well, it is usually because the roller is not providing enough pressure. You can try the following solutions:
Lift the gear at the ba...
MTB-CUT 180T
"Cutting misalignment is usually caused by:
Center Cutting Not Enabled: Make sure the “Center Cutting” option is enabled on the cutting page so the machine automatically positions...
MTB-CUT 180T
Laptop screen protectors have a much longer cutting path, and during long-distance cutting, the material may experience slight deviation due to blade pressure. This can cause inacc...
MTB-CUT M288
You can follow the video tutorial provided below to operate the MTB-CUT M288 intelligent cutting and pasting machine.
The video demonstrates all the required steps for proper cutt...
MTB-CUT 180T
Large-size screen protectors such as iPad and laptop films have longer cutting paths.
During long-distance cutting, the material may slightly shift due to the blade pressure, whic...
MTB-CUT 180T
This issue usually occurs when the material size settings do not match the template, especially when cutting full back films.
Recommended Solution
When cutting full back film, pl...
MTB-CUT 180T
The correct cutting parameters depend on the materials being used. Here are some recommended settings for common materials:
Material | Back Film | Four Layer Soft Film | Explosion-...
MTB-CUT 180T
We provide a variety of cutting materials such as HD clear, matte, privacy, and anti-blue-ray films. Prices vary depending on the material and functionality, but all options are ge...
MTB-CUT 180T
In most cases, you can keep the cutting speed at the default value of 200.
This setting works well for the majority of materials.
When to reduce the speed
You should lower the...
MTB-CUT 180T
When cutting full-screen back films, please disable the "Cut Center" option on the cutting page.
Additionally, ensure that the material size is set to 180mm x 120mm.
Since the ful...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size main...
MTB-CUT 180T
"The continuous running of the motor may be caused by the following reasons:
Poor motor wiring connection: Check if the motor wiring is secure. If there is any looseness or poor co...
MTB-CUT 180T
The correct material (paper) size setting is:
180 mm × 120 mm
Please make sure the material is placed in the correct direction before cutting.
MTB-CUT 180T
This issue is usually caused by the Blade Holder scale being set too high.
Please try to reduce the Blade Holder scale setting.
Important Note
Pay attention to the blade exposur...
MTB-CUT 180T
The blade size (blade holder scale) should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade size, while thi...
MTB-CUT 180T
"The recommended cutting parameters for back films are:
Material Size: 180mm width × 120mm height
Pressure: 300
Blade Holder Scale: 5
Speed: 200
These settings are suit...
MTB-CUT 180T
"If the cutting machine stops halfway, it is usually due to incorrect material size or parameter settings. When the cutting carriage reaches the edge, it triggers the edge sensor,...
MTB-CUT 180T Pro
Please keep speed at 200.
The blade holder scale should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade s...
MTB-CUT 180T
This issue may be caused by:
The material sensor being blocked
A mainboard malfunction
Please try the following steps:
Go to Settings
Disable the “Auto Loading&rdq...
MTB-CUT 180T
"When the sensor malfunctions, the machine may fail to detect or automatically load the cutting material. You can try the following two approaches:
Replace the Sensor
If the senso...
Showing 21
to 40
of 78 results
