Showing 127 results
for
"material settings"
MTB-CUT 180T
"The material size setting depends on the type of material you are using.
Mietubl's standard material size is 180mm (width) x 120mm (height).
You can configure your machine accord...
MTB-CUT 180T
"When cutting back films, you need to consider both the pattern position and the cutting range. You can adjust these by setting the material size and enabling or disabling center c...
MTB-CUT 180T
When placing the cutting material, please follow these guidelines:
Place the material on the right side of the machine’s platform.
Make sure the material is completely flat...
MTB-CUT 180T
The Cut Centered option is used to position the cutting area exactly in the center of the material size you set.
For example, if your material size is set to 180mm (width) ×...
MTB-CUT 180T
Yes, the screen protector machine can cut PET material. However, you may need to adjust the machine settings, and keep in mind that PET material is more likely to wear out the cutt...
MTB-CUT 180T
This issue usually occurs when the material size settings do not match the template, especially when cutting full back films.
Recommended Solution
When cutting full back film, pl...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size main...
MTB-CUT 180T
The blade size (blade holder scale) should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade size, while thi...
MTB-CUT 180T
"If the cutting machine stops halfway, it is usually due to incorrect material size or parameter settings. When the cutting carriage reaches the edge, it triggers the edge sensor,...
MTB-CUT 180T Pro
Please keep speed at 200.
The blade holder scale should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade s...
MTB-CUT 180T
"If the tablet screen protector is not cutting well, it is usually because the roller is not providing enough pressure. You can try the following solutions:
Lift the gear at the ba...
MTB-CUT 180T
Laptop screen protectors have a much longer cutting path, and during long-distance cutting, the material may experience slight deviation due to blade pressure. This can cause inacc...
MTB-CUT M688/M288
You can follow the video tutorial provided below to operate the MTB-CUT M288 intelligent cutting and pasting machine.
The video demonstrates all the required steps for proper cutt...
MTB-CUT 180T
Large-size screen protectors such as iPad and laptop films have longer cutting paths.
During long-distance cutting, the material may slightly shift due to the blade pressure, whic...
MTB-CUT 180T
The correct cutting parameters depend on the materials being used. Here are some recommended settings for common materials:
Material | Back Film | Four Layer Soft Film | Explosion-...
MTB-CUT 180T
"The continuous running of the motor may be caused by the following reasons:
Poor motor wiring connection: Check if the motor wiring is secure. If there is any looseness or poor co...
MTB-CUT 180T
"The recommended cutting parameters for back films are:
Material Size: 180mm width × 120mm height
Pressure: 300
Blade Holder Scale: 5
Speed: 200
These settings are suit...
MTB-CUT 180T
This issue may be caused by:
The material sensor being blocked
A mainboard malfunction
Please try the following steps:
Go to Settings
Disable the “Auto Loading&rdq...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
The blade size (blade holder scale) should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade size, while thi...
Showing 21
to 40
of 127 results
