Showing 95 results
for
"blade settings"
MTB-CUT 180T
"Prolonged use of excessively high blade holder settings and cutting pressure may lead to a decline in the precision of the blade holder, resulting in the inability to properly cut...
MTB-CUT 180T
If you want to improve cutting results, please follow these tips:
Check Wheel Position
Make sure all pinch wheels firmly press on the cutting material, and their position is on t...
MTB-CUT 180T
The blade size (blade holder scale) should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade size, while thi...
MTB-CUT 180T
The blade size (blade holder scale) should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade size, while thi...
MTB-CUT 180T Pro
Please keep speed at 200.
The blade holder scale should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade s...
MTB-CUT 180T
"When the film bulges during cutting, it is usually caused by the following reasons:
Blade holder depth set too high – Excessive cutting depth can cause uneven stress on the materi...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size mainl...
MTB-CUT 180T
This issue is usually caused by the Blade Holder scale being set too high.
Please try to reduce the Blade Holder scale setting.
Important Note
Pay attention to the blade exposur...
MTB-CUT 180T
"When replacing the blade, simply press the top of the blade holder to remove the old blade and insert a new one.
Please refer to the video below for detailed instructions on how t...
MTB-CUT 180T
If the blade does not drop properly during cutting, this issue is most likely caused by a mainboard malfunction.
The blade-down action is controlled by the Y-axis motor signal fro...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size main...
MTB-CUT 180T
Under normal conditions, we recommend replacing the blade after approximately: 300 cuts
However, this is only a recommended value.
The actual blade lifespan may increase or decre...
MTB-CUT 180T
"The rubber cutting mat strip located beneath the blade serves to prevent blade wear and extend the blade’s service life.
However, after prolonged use, the surface of the mat strip...
MTB-CUT 180T
"If the Car moves after you initiate cutting, but the blade holder does not drop, this issue may be caused by one of the following reasons:
Insufficient power supply – Please verif...
MTB-CUT 180T
When you first receive the machine, you must remove the transport-locking screw located on the back of the device to prevent damage to the blade carriage.
During normal daily us...
MTB-CUT 180T Pro
The Blade Holder Scale depends on the thickness of the material.
For most TPU screen protector materials, the following settings are recommended:
Blade Size: 5
Pressure: 300
&n...
MTB-CUT 180T Pro
The Blade Holder Scale depends on the thickness of the material.
For most Back Film materials, the recommended settings are:
Blade Size: 4
Pressure: 300
These settings...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
"Here are some default setting ：material size is 180mm width × 120mm height.
Cutting pressure: 300
Cutting speed: 200
Blade holder scale: 5
These default settings are sui...
MTB-CUT 180T
If you encounter problems while configuring the machine, you can try using the following default settings, which work for most materials:
Recommended Default Settings
Speed: 20...
Showing 1
to 20
of 95 results
