Showing 56 results
for
"replace roller assembly"
MTB-CUT M288
"The MTB-CUT M288 uses an integrated clip-on screen design.
If you need to replace the screen, simply use a tool to release the clips and connect the new screen to the power cable....
MTB-CUT M188
A “Time Out” message usually means that there is a communication failure between the screen and the mainboard. This can be caused by:
Loose or Damaged Screen Cable
Op...
MTB-CUT M188
"In the MTB-CUT M188 screen protector cutting machine, the rubber strip at the bottom of the cutting module is designed to protect the cutting blade and extend the lifespan of both...
MTB-CUT M188
This video provides a step-by-step guide on how to replace the screen of MTB-CUT M188 screen protector cutting machine. https://mietublcom.oss-accelerate.aliyuncs.com/service/video...
MTB-CUT M188
This video provides a step-by-step guide on how to replace the cutting module spring of the MTB-CUT M188 screen protector cutting machine to resolve the issue of the cutting module...
MTB-CUT M188
This video provides a guide on how to replace the cutting module of the MTB-CUT M188 screen protector cutting machine. https://mietublcom.oss-accelerate.aliyuncs.com/service/videos...
MTB-CUT M188
"If the screen protector cutting machine is unable to load cutting materials properly, it may be due to a malfunctioning sensor.
This video provides a step-by-step guide on how to...
MTB-CUT M188
"If the cutting Car does not stop automatically when it moves to either side and produces a loud noise, it may be due to a malfunctioning limit switch, which prevents the cutting C...
MTB-CUT M188
"The MTB-CUT M288 intelligent film cutting and pasting machine uses a modular screen design for easy maintenance and replacement.
If necessary, you can simply remove the screen and...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine fails to automatically secure the screen protector or if the vacuum pump does not start, it may indicate a vacuum...
MTB-CUT 180T
When the machine beeps with a repeated “bip bip” sound and fails to start cutting, it usually means that the X-axis or Y-axis cannot operate normally.
Common causes include a stuc...
MTB-CUT 180T
"A knocking sound from the machine can be caused by the following reasons and can be resolved as follows:
Transport screws not removed (for new machines)
New machines are shippe...
MTB-CUT 180T
"You can refer to the following video for instructions on replacing the motherboard.
You can obtain a replacement motherboard from your local distributor or contact the dealer who...
MTB-CUT 180T
"When the film bulges during cutting, it is usually caused by the following reasons:
Blade holder depth set too high – Excessive cutting depth can cause uneven stress on the materi...
MTB-CUT 180T
"Here is a video on how to replace the cutting car.
https://osscdn.mietubl.com/video/202508141609.mp4"
MTB-CUT 180T
"When the sensor malfunctions, the machine may fail to detect or automatically load the cutting material. You can try the following two approaches:
Replace the Sensor
If the senso...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
"If your device displays the error message “Unable to communicate with the device (13904)”, please navigate to “My” → “About” → “Check if the QR code is displayed”.
If the QR code...
MTB-CUT 180T
"Prolonged use of excessively high blade holder settings and cutting pressure may lead to a decline in the precision of the blade holder, resulting in the inability to properly cut...
MTB-CUT 180T
"If the machine is unable to cut screen protector materials properly, please first try the following steps:
Replace the blade and blade holder with new ones.
Set the cutting pre...
Showing 21
to 40
of 56 results
