Showing 83 results
for
"startup app"
MTB-CUT 180T
"A slow APP startup is usually caused by excessive cached data slowing down performance. You can try the following steps:
Clear the Cache: Follow the steps shown in the video to go...
MTB-CUT 180T
"You can set the Cutter App as the default startup app by following these steps:
Open the device System Settings.
Locate Cutter App (usually found under App Management or Defaul...
MTB-CUT 180T
"If the machine displays a ""Timeout"" error on startup and the ""Reconnect"" button is unresponsive, it usually means the screen cannot properly connect to the mainboard. Possible...
MTB-CUT 180T
"If the 180T screen protector cutting machine displays a “Reconnection” message after startup, it is likely that there is an issue with the system firmware.
You can resolve this by...
MTB-CUT M188
"If the machine displays a “connection timeout” message during startup, it typically indicates a mainboard failure.
Please contact your local distributor to obtain a replacement ma...
MTB-CUT 180T
This happens because the APP version was rolled back during the factory reset.
When the machine is reset, the system returns to the earliest APP version, and many new models added...
MTB-CUT 180T
"If you start the screen protector cutting machine but the Cutter app does not launch automatically, this may be because the device was recently reset and the Cutter app has not be...
MTB-CUT 180T
If the screen protector cutting machine cannot load phone models and the cutting page appears blank, it is usually caused by a language setting issue or corrupted software data.
S...
MTB-CUT 180T
If the screen protector cutting machine cannot load phone models and the cutting page appears blank, it is usually caused by a language setting issue or corrupted software data.
S...
MTB-CUT 180T
This issue is usually caused by app cache or data errors, preventing the app from running properly.
Please follow the instruction video to clear the app cache and data, then reope...
MTB-CUT 180T
"You can reinstall the Cutter App by following these steps:
Open Browser
On the smart screen protector cutting machine, run the Chrome browser and enter the following address:
ht...
MTB-CUT 180T
"Cache is essential for ensuring the stable operation of the app. However, under certain circumstances — such as after an app update or when data models fail to load — clearing the...
MTB-CUT 180T
"We periodically release updates for the machine's app to improve performance and functionality.
The password required to perform the app upgrade is ""1212"".
Please note:
App...
MTB-CUT 180T
If the screen turns off automatically abnormally, it may be caused by a short circuit or internal wiring issue.
Please click the WhatsApp button below and send the following to ou...
MTB-CUT M188
If your MTB-CUT M188 displays a “Time Out” or “Reconnection” error after startup, please follow the steps below:
Step 1: Check the machine barcode
Check t...
MTB-CUT 180T
"If the machine is continuously beeping and not working properly, please try the following steps:
Force Restart: Press and hold the power button for 20 seconds to force the machine...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT 180T
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
Showing 1
to 20
of 83 results
