Showing 65 results
for
"replace motherboard"
MTB-CUT 180T
"When the film bulges during cutting, it is usually caused by the following reasons:
Blade holder depth set too high – Excessive cutting depth can cause uneven stress on the materi...
MTB-CUT 180T
"Here is a video on how to replace the cutting car.
https://osscdn.mietubl.com/video/202508141609.mp4"
MTB-CUT 180T
"When the sensor malfunctions, the machine may fail to detect or automatically load the cutting material. You can try the following two approaches:
Replace the Sensor
If the senso...
MTB-CUT 180T
If the machine is showing “Unable Connecting to Mainboard”, the machine’s mainboard may be faulty.
In this case, the mainboard may need to be replaced....
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
"If your device displays the error message “Unable to communicate with the device (13904)”, please navigate to “My” → “About” → “Check if the QR code is displayed”.
If the QR code...
MTB-CUT 180T
If the blade does not drop properly during cutting, this issue is most likely caused by a mainboard malfunction.
The blade-down action is controlled by the Y-axis motor signal fro...
MTB-CUT 180T
"Prolonged use of excessively high blade holder settings and cutting pressure may lead to a decline in the precision of the blade holder, resulting in the inability to properly cut...
MTB-CUT 180T
Please open the machine’s WiFi list and check whether available WiFi networks can be detected normally.
If the machine cannot detect or display WiFi networks, the machine’s networ...
MTB-CUT 180T
"If the machine is unable to cut screen protector materials properly, please first try the following steps:
Replace the blade and blade holder with new ones.
Set the cutting pre...
MTB-CUT 180T
"If the cutting Car fails to stop properly when reaching the edge and produces a loud noise, it is likely due to an error in the Car’s limit positioning.
You can replace specific p...
MTB-CUT M688/M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M688/M288
"The MTB-CUT M288 intelligent film cutting and pasting machine uses a modular fixture design.
If the fixture is unable to properly hold the phone, you can quickly replace it using...
MTB-CUT M688/M288
"The silicone pad is one of the few parts in the MTB-CUT M288 intelligent film cutting and pasting machine that requires replacement.
It is essential for the proper installation of...
MTB-CUT M688/M288
"White edges when applying film with the MTB-CUT M288 may be caused by the following reasons:
Firmware issue – Please ensure your firmware version is V25.0431.
https://osscdn.mi...
MTB-CUT M188
If your MTB-CUT M188 displays “Time Out” after powering on, it is usually caused by an abnormal serial communication between the screen and the mainboard.
This situati...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"The MTB-CUT M288 intelligent film cutting and pasting machine uses a modular fixture design.
If the fixture is unable to properly hold the phone, you can quickly replace it using...
MTB-CUT M188
"The silicone pad is one of the few parts in the MTB-CUT M288 intelligent film cutting and pasting machine that requires replacement.
It is essential for the proper installation of...
MTB-CUT 180T
1. Check whether the Wi-Fi module is working
Open the Wi-Fi list page on your machine and confirm:
Whether the machine can scan and display the Wi-Fi networks around you;
Whethe...
Showing 41
to 60
of 65 results
