Showing 24 results
for
"car"
MTB-CUT 180T
"This video provides a step-by-step guide on how to repair the cutting Car.
Please note:
When reinstalling the Car, pay close attention to the clearance between the Car and the gu...
MTB-CUT 180T
"The machine is equipped with X-axis and Y-axis motors. The X-axis motor is responsible for controlling the horizontal (left-right) movement of the cutting Car.
If the X-axis belt...
MTB-CUT 180T
"Loosening of the car from the guide rail is one of the main causes of cutting distortion.
If such an issue occurs, it is necessary to adjust the clearance between the car and the...
MTB-CUT 180T
"If the cutting Car fails to stop properly when reaching the edge and produces a loud noise, it is likely due to an error in the Car’s limit positioning.
You can replace specific p...
MTB-CUT 180T
"Here is a video on how to replace the cutting car.
https://osscdn.mietubl.com/video/202508141609.mp4"
MTB-CUT M188
"If the cutting Car does not stop automatically when it moves to either side and produces a loud noise, it may be due to a malfunctioning limit switch, which prevents the cutting C...
MTB-CUT 180T
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT M288
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT 180T
Please first confirm the specific issue you are facing:
1. If the blade holder does not go down during cutting
This is usually caused by a mainboard malfunction.
In this case, t...
MTB-CUT 180T
"If the Car moves after you initiate cutting, but the blade holder does not drop, this issue may be caused by one of the following reasons:
Insufficient power supply – Please verif...
MTB-CUT M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT 180T
When you first receive the machine, you must remove the transport-locking screw located on the back of the device to prevent damage to the blade carriage.
During normal daily us...
MTB-CUT 180T
"In most cases, templates are designed with precise and regular shapes.
If the shapes are not forming properly, it may be caused by:
A loose cutting carriage – Please check if t...
MTB-CUT 180T
"A knocking sound from the machine can be caused by the following reasons and can be resolved as follows:
Transport screws not removed (for new machines)
New machines are shippe...
MTB-CUT 180T
"If the cutting process cannot start, please follow these steps to troubleshoot:
Restart the machine: Power off and then restart the device.
Check carriage reset: When the machi...
MTB-CUT 180T
If the camera lens cutout appears oval-shaped, it is likely caused by a loose carriage.
Please follow these steps:
Refer to the instructional video to refit the carriage onto the...
MTB-CUT 180T
"This error usually means the cutting carriage (X-axis motor) is stuck or cannot find its home position.
- Step 1: Press and hold the power button for 20 seconds to restart the mac...
MTB-CUT 180T
"Unexpected interruptions may lead to the loss of device firmware. This video provides step-by-step instructions on how to generate the firmware for your device and reinstall the s...
MTB-CUT 180T
"If the machine remains stuck on the logo screen after powering on and cannot proceed to the next operation, reinstalling the system may resolve the issue.
This video provides a st...
Showing 1
to 20
of 24 results
