Showing 72 results
for
"replace blade"
MTB-CUT 180T
"Prolonged use of excessively high blade holder settings and cutting pressure may lead to a decline in the precision of the blade holder, resulting in the inability to properly cut...
MTB-CUT 180T
If you want to improve cutting results, please follow these tips:
Check Wheel Position
Make sure all pinch wheels firmly press on the cutting material, and their position is on t...
MTB-CUT 180T
The blade size (blade holder scale) should be adjusted based on the thickness and hardness of the film material.
Thicker or harder materials require a higher blade size, while thi...
MTB-CUT 180T
"When the film bulges during cutting, it is usually caused by the following reasons:
Blade holder depth set too high – Excessive cutting depth can cause uneven stress on the materi...
MTB-CUT 180T
"When replacing the blade, simply press the top of the blade holder to remove the old blade and insert a new one.
Please refer to the video below for detailed instructions on how t...
MTB-CUT 180T
"The rubber cutting mat strip located beneath the blade serves to prevent blade wear and extend the blade’s service life.
However, after prolonged use, the surface of the mat strip...
MTB-CUT 180T
If the blade does not drop properly during cutting, this issue is most likely caused by a mainboard malfunction.
The blade-down action is controlled by the Y-axis motor signal fro...
MTB-CUT 180T
When you first receive the machine, you must remove the transport-locking screw located on the back of the device to prevent damage to the blade carriage.
During normal daily us...
MTB-CUT 180T
Please first confirm the specific issue you are facing:
1. If the blade holder does not go down during cutting
This is usually caused by a mainboard malfunction.
In this case, t...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size mainl...
MTB-CUT 180T
"If the Car moves after you initiate cutting, but the blade holder does not drop, this issue may be caused by one of the following reasons:
Insufficient power supply – Please verif...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT M188
"In the MTB-CUT M188 screen protector cutting machine, the rubber strip at the bottom of the cutting module is designed to protect the cutting blade and extend the lifespan of both...
MTB-CUT 180T
When the machine beeps with a repeated “bip bip” sound and fails to start cutting, it usually means that the X-axis or Y-axis cannot operate normally.
Common causes include a stuc...
MTB-CUT 180T
"The machine features an independent housing design.
In the event of housing damage, you can replace the machine’s outer shell separately without needing to replace the entire unit...
MTB-CUT 180T
"The intelligent film cutting machine is easy to set up.
The standard settings include cutting pressure, cutting speed, blade holder scale, and material size.
Material size main...
MTB-CUT 180T
"This can be caused by several issues:
- Incorrect Power Supply: Ensure you are using the original power adapter. An incorrect adapter can cause insufficient power.
- Blade Pressu...
MTB-CUT 180T
"If the machine is unable to cut screen protector materials properly, please first try the following steps:
Replace the blade and blade holder with new ones.
Set the cutting pre...
MTB-CUT 180T
"The parameter settings of a screen protector cutting machine mainly depend on the physical properties of the material.
The thicker the material, the higher the blade holder scale...
MTB-CUT 180T
"The default parameters of the screen protector cutting machine — blade holder scale 5 and cutting pressure 300g — are suitable for most materials, including HD clear film.
If the...
Showing 1
to 20
of 72 results
