Showing 81 results
for
"replace mainboard"
MTB-CUT 180T
"If the Car moves after you initiate cutting, but the blade holder does not drop, this issue may be caused by one of the following reasons:
Insufficient power supply – Please verif...
MTB-CUT 180T
This issue usually occurs after replacing the machine’s mainboard.
Because the machine ID is originally bound to the old mainboard, installing a new mainboard requires the I...
MTB-CUT 180T
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT M688/M288
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT 180T
"A knocking sound from the machine can be caused by the following reasons and can be resolved as follows:
Transport screws not removed (for new machines)
New machines are shippe...
MTB-CUT 180T
1. Check whether the Wi-Fi module is working
Open the Wi-Fi list page on your machine and confirm:
Whether the machine can scan and display the Wi-Fi networks around you;
Whethe...
MTB-CUT 180T
Error 1002 indicates that a device port is occupied.
In this case, you can try the following steps:
Restart the device and go to "My" → "About This Device" to check if the Q...
MTB-CUT 180T
"If your machine stays in the “Status Checking” state for a long time, it may be caused by network delays or communication errors. Please try the following steps:
Restart the machi...
MTB-CUT 180T
"If the 180T screen protector cutting machine displays a “Reconnection” message after startup, it is likely that there is an issue with the system firmware.
You can resolve this by...
MTB-CUT M188
"If the machine displays a “connection timeout” message during startup, it typically indicates a mainboard failure.
Please contact your local distributor to obtain a replacement ma...
MTB-CUT 180T
"If you experience unresponsive touch or system crashes, it may be necessary to replace the machine’s screen.
This video provides a step-by-step guide on how to replace the screen...
MTB-CUT 180T
"The rubber cutting mat strip located beneath the blade serves to prevent blade wear and extend the blade’s service life.
However, after prolonged use, the surface of the mat strip...
MTB-CUT 180T
"The intelligent film cutting machine has two belts:
One is used to control the left-right movement of the carriage
https://osscdn.mietubl.com/images/X-axis-belt.jpg
The othe...
MTB-CUT 180T
It is generally recommended to replace the blade after around 300 cuts.
The actual replacement frequency may vary depending on material type and usage. If cutting quality...
MTB-CUT 180T
"Our smart screen protector cutting machine has no cutting limit, and we will continue to provide template and data updates to ensure long-term usability.
However, please note that...
MTB-CUT 180T
"When replacing the blade, simply press the top of the blade holder to remove the old blade and insert a new one.
Please refer to the video below for detailed instructions on how t...
MTB-CUT 180T
If you want to improve cutting results, please follow these tips:
Check Wheel Position
Make sure all pinch wheels firmly press on the cutting material, and their position is on t...
MTB-CUT 180T
Please follow the blade replacement instructions to correctly insert or replace the blade in the Blade Holder.
If you are unable to press the Blade Holder, the blade may be stuck...
MTB-CUT 180T
"The machine is equipped with X-axis and Y-axis motors. The X-axis motor is responsible for controlling the horizontal (left-right) movement of the cutting Car.
If the X-axis belt...
MTB-CUT 180T
"The rollers are primarily responsible for controlling the forward and backward movement of the material.
Please note: Pay close attention to the position of the black pads on the...
Showing 21
to 40
of 81 results
