Showing 100 results
for
"startup issue"
MTB-CUT 180T
"If the machine displays a ""Timeout"" error on startup and the ""Reconnect"" button is unresponsive, it usually means the screen cannot properly connect to the mainboard. Possible...
MTB-CUT 180T
"If the 180T screen protector cutting machine displays a “Reconnection” message after startup, it is likely that there is an issue with the system firmware.
You can resolve this by...
MTB-CUT 180T
"A slow APP startup is usually caused by excessive cached data slowing down performance. You can try the following steps:
Clear the Cache: Follow the steps shown in the video to go...
MTB-CUT M188
"If the machine displays a “connection timeout” message during startup, it typically indicates a mainboard failure.
Please contact your local distributor to obtain a replacement ma...
MTB-CUT 180T
If the screen turns off automatically abnormally, it may be caused by a short circuit or internal wiring issue.
Please click the WhatsApp button below and send the following to ou...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT M188
If your MTB-CUT M188 displays a “Time Out” or “Reconnection” error after startup, please follow the steps below:
Step 1: Check the machine barcode
Check t...
MTB-CUT 180T
If the screen protector cutting machine cannot load phone models and the cutting page appears blank, it is usually caused by a language setting issue or corrupted software data.
S...
MTB-CUT 180T
If the screen protector cutting machine cannot load phone models and the cutting page appears blank, it is usually caused by a language setting issue or corrupted software data.
S...
MTB-CUT 180T
"If the machine is continuously beeping and not working properly, please try the following steps:
Force Restart: Press and hold the power button for 20 seconds to force the machine...
MTB-CUT 180T
If the screen protector cutting machine cannot load phone models and the cutting page appears blank, it is usually caused by a language setting issue or corrupted software data.
S...
MTB-CUT 180T
If the screen protector cutting machine cannot load phone models and the cutting page appears blank, it is usually caused by a language setting issue or corrupted software data.
S...
MTB-CUT 180T
"You can set the Cutter App as the default startup app by following these steps:
Open the device System Settings.
Locate Cutter App (usually found under App Management or Defaul...
MTB-CUT 180T
If no models are displayed after updating the machine and you only see “K_product”, this is usually because the APP data loading process was interrupted after the upgra...
MTB-CUT M688/M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT 180T
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT M688/M288
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT 180T
If the machine displays a “Time Out” error during film cutting, please follow the steps below:
1. Check whether the motherboard is connected
On the machine, go to:...
MTB-CUT 180T
This issue may be related to the auto-loading function or hardware components.
Please disable “Auto-loading” and try cutting any screen protector model to check whethe...
Showing 1
to 20
of 100 results
