Showing 66 results
for
"replace"
MTB-CUT M188
"If the screen protector cutting machine is unable to load cutting materials properly, it may be due to a malfunctioning sensor.
This video provides a step-by-step guide on how to...
MTB-CUT M188
"If the cutting Car does not stop automatically when it moves to either side and produces a loud noise, it may be due to a malfunctioning limit switch, which prevents the cutting C...
MTB-CUT M188
"The MTB-CUT M288 intelligent film cutting and pasting machine uses a modular screen design for easy maintenance and replacement.
If necessary, you can simply remove the screen and...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine fails to automatically secure the screen protector or if the vacuum pump does not start, it may indicate a vacuum...
MTB-CUT 180T
When the machine beeps with a repeated “bip bip” sound and fails to start cutting, it usually means that the X-axis or Y-axis cannot operate normally.
Common causes include a stuc...
MTB-CUT 180T
Please first confirm the specific issue you are facing:
1. If the blade holder does not go down during cutting
This is usually caused by a mainboard malfunction.
In this case, t...
MTB-CUT 180T
"A knocking sound from the machine can be caused by the following reasons and can be resolved as follows:
Transport screws not removed (for new machines)
New machines are shippe...
MTB-CUT 180T
"You can refer to the following video for instructions on replacing the motherboard.
You can obtain a replacement motherboard from your local distributor or contact the dealer who...
MTB-CUT 180T
"When the film bulges during cutting, it is usually caused by the following reasons:
Blade holder depth set too high – Excessive cutting depth can cause uneven stress on the materi...
MTB-CUT 180T
"Here is a video on how to replace the cutting car.
https://osscdn.mietubl.com/video/202508141609.mp4"
MTB-CUT 180T
"When the sensor malfunctions, the machine may fail to detect or automatically load the cutting material. You can try the following two approaches:
Replace the Sensor
If the senso...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
"If your device displays the error message “Unable to communicate with the device (13904)”, please navigate to “My” → “About” → “Check if the QR code is displayed”.
If the QR code...
MTB-CUT 180T
"Prolonged use of excessively high blade holder settings and cutting pressure may lead to a decline in the precision of the blade holder, resulting in the inability to properly cut...
MTB-CUT 180T
"If the machine is unable to cut screen protector materials properly, please first try the following steps:
Replace the blade and blade holder with new ones.
Set the cutting pre...
MTB-CUT 180T
"If the cutting Car fails to stop properly when reaching the edge and produces a loud noise, it is likely due to an error in the Car’s limit positioning.
You can replace specific p...
MTB-CUT M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M288
"The MTB-CUT M288 intelligent film cutting and pasting machine uses a modular fixture design.
If the fixture is unable to properly hold the phone, you can quickly replace it using...
MTB-CUT M288
"The silicone pad is one of the few parts in the MTB-CUT M288 intelligent film cutting and pasting machine that requires replacement.
It is essential for the proper installation of...
MTB-CUT M288
"White edges when applying film with the MTB-CUT M288 may be caused by the following reasons:
Firmware issue – Please ensure your firmware version is V25.0431.
https://osscdn.mi...
Showing 21
to 40
of 66 results
