Showing 57 results
for
"replace housing"
MTB-CUT M188
"If the screen protector cutting machine is unable to load cutting materials properly, it may be due to a malfunctioning sensor.
This video provides a step-by-step guide on how to...
MTB-CUT M188
"If the cutting Car does not stop automatically when it moves to either side and produces a loud noise, it may be due to a malfunctioning limit switch, which prevents the cutting C...
MTB-CUT M188
"The MTB-CUT M288 intelligent film cutting and pasting machine uses a modular screen design for easy maintenance and replacement.
If necessary, you can simply remove the screen and...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine fails to automatically secure the screen protector or if the vacuum pump does not start, it may indicate a vacuum...
MTB-CUT 180T
When the machine beeps with a repeated “bip bip” sound and fails to start cutting, it usually means that the X-axis or Y-axis cannot operate normally.
Common causes include a stuc...
MTB-CUT 180T
Please first confirm the specific issue you are facing:
1. If the blade holder does not go down during cutting
This is usually caused by a mainboard malfunction.
In this case, t...
MTB-CUT M188
If your MTB-CUT M188 displays a “Time Out” or “Reconnection” error after startup, please follow the steps below:
Step 1: Check the machine barcode
Check t...
MTB-CUT 180T
If your WiFi connection is unstable or cannot connect properly, please follow these steps:
1. Check WiFi list visibility
If you can see the WiFi list, the issue is likely not a h...
MTB-CUT 180T
This issue may be related to the auto-loading function or hardware components.
Please disable “Auto-loading” and try cutting any screen protector model to check whethe...
MTB-CUT 180T
Please go to: “Mine” → “About this machine” and check whether the device QR code is displayed properly.
If the QR code is not displayed: it may indica...
MTB-CUT 180T
"A knocking sound from the machine can be caused by the following reasons and can be resolved as follows:
Transport screws not removed (for new machines)
New machines are shippe...
MTB-CUT 180T
"You can refer to the following video for instructions on replacing the motherboard.
You can obtain a replacement motherboard from your local distributor or contact the dealer who...
MTB-CUT 180T
This issue may be caused by a WiFi module failure in the screen assembly.
Step 1: Check whether the WiFi list can be loaded
Please open the WiFi settings page and check whether t...
MTB-CUT 180T
"When the film bulges during cutting, it is usually caused by the following reasons:
Blade holder depth set too high – Excessive cutting depth can cause uneven stress on the materi...
MTB-CUT 180T
"Here is a video on how to replace the cutting car.
https://osscdn.mietubl.com/video/202508141609.mp4"
MTB-CUT 180T
"When the sensor malfunctions, the machine may fail to detect or automatically load the cutting material. You can try the following two approaches:
Replace the Sensor
If the senso...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
"If your device displays the error message “Unable to communicate with the device (13904)”, please navigate to “My” → “About” → “Check if the QR code is displayed”.
If the QR code...
MTB-CUT 180T
"Prolonged use of excessively high blade holder settings and cutting pressure may lead to a decline in the precision of the blade holder, resulting in the inability to properly cut...
MTB-CUT 180T
"If the machine is unable to cut screen protector materials properly, please first try the following steps:
Replace the blade and blade holder with new ones.
Set the cutting pre...
Showing 21
to 40
of 57 results
