Showing 60 results
for
"replace silicone pad"
MTB-CUT 180T
"When the sensor malfunctions, the machine may fail to detect or automatically load the cutting material. You can try the following two approaches:
Replace the Sensor
If the senso...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
"If your device displays the error message “Unable to communicate with the device (13904)”, please navigate to “My” → “About” → “Check if the QR code is displayed”.
If the QR code...
MTB-CUT 180T
"Prolonged use of excessively high blade holder settings and cutting pressure may lead to a decline in the precision of the blade holder, resulting in the inability to properly cut...
MTB-CUT 180T
"If the machine is unable to cut screen protector materials properly, please first try the following steps:
Replace the blade and blade holder with new ones.
Set the cutting pre...
MTB-CUT 180T
"If the cutting Car fails to stop properly when reaching the edge and produces a loud noise, it is likely due to an error in the Car’s limit positioning.
You can replace specific p...
MTB-CUT M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M288
"The MTB-CUT M288 intelligent film cutting and pasting machine uses a modular fixture design.
If the fixture is unable to properly hold the phone, you can quickly replace it using...
MTB-CUT M288
"White edges when applying film with the MTB-CUT M288 may be caused by the following reasons:
Firmware issue – Please ensure your firmware version is V25.0431.
https://osscdn.mi...
MTB-CUT M188
If your MTB-CUT M188 displays “Time Out” after powering on, it is usually caused by an abnormal serial communication between the screen and the mainboard.
This situati...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"The MTB-CUT M288 intelligent film cutting and pasting machine uses a modular fixture design.
If the fixture is unable to properly hold the phone, you can quickly replace it using...
MTB-CUT 180T
1. Check whether the Wi-Fi module is working
Open the Wi-Fi list page on your machine and confirm:
Whether the machine can scan and display the Wi-Fi networks around you;
Whethe...
MTB-CUT 180T
When you first receive the machine, you must remove the transport-locking screw located on the back of the device to prevent damage to the blade carriage.
During normal daily us...
MTB-CUT M288
The “Reconnection” message means that the screen cannot establish a proper connection with the mainboard.
This issue is typically caused by a loose or faulty screen-to...
MTB-CUT 180T
If the machine displays a “Time Out” error during film cutting, please follow the steps below:
1. Check whether the motherboard is connected
On the machine, go to:...
MTB-CUT 180T
This error is usually caused by a mainboard malfunction.
To fix the issue, please follow these steps:
Replace the mainboard following the instructional video.
Before replacing...
MTB-CUT 180T
According to your description, this issue is usually caused by a short circuit on the motherboard or a motherboard failure. When the motherboard fails to complete the self-test, th...
MTB-CUT 180T
If the blade does not drop properly during cutting, this issue is most likely caused by a mainboard malfunction.
The blade-down action is controlled by the Y-axis motor signal fro...
MTB-CUT M288
If your touch screen is not responding properly, please check the following:
1. Confirm you are using the original power adapter
The original adapter should be 24V / 2.7A.
Usi...
Showing 41
to 60
of 60 results
