Showing 224 results
for
"screen protector cutting machine"
MTB-CUT 180T
"When the sensor malfunctions, the machine may fail to detect or automatically load the cutting material. You can try the following two approaches:
Replace the Sensor
If the senso...
MTB-CUT 180T
"When the film bulges during cutting, it is usually caused by the following reasons:
Blade holder depth set too high – Excessive cutting depth can cause uneven stress on the materi...
MTB-CUT 180T
If you want to improve cutting results, please follow these tips:
Check Wheel Position
Make sure all pinch wheels firmly press on the cutting material, and their position is on t...
MTB-CUT 180T
"The rubber cutting mat strip located beneath the blade serves to prevent blade wear and extend the blade’s service life.
However, after prolonged use, the surface of the mat strip...
MTB-CUT 180T
The Cut Centered option is used to position the cutting area exactly in the center of the material size you set.
For example, if your material size is set to 180mm (width) ×...
MTB-CUT 180T
"The cutting machine may work slowly if the cutting speed setting is too low.
Please try setting the cutting speed to the default value of 200 and then attempt cutting again.
If...
MTB-CUT 180T
This issue usually occurs when the material size settings do not match the template, especially when cutting full back films.
Recommended Solution
When cutting full back film, pl...
MTB-CUT 180T
"Cutting misalignment is usually caused by:
Center Cutting Not Enabled: Make sure the “Center Cutting” option is enabled on the cutting page so the machine automatically positions...
MTB-CUT 180T
This issue is usually caused by corrupted cached data in the system.
Please follow the steps below:
Clear the APP cache
Follow the method shown in the video to clear the Cutter...
MTB-CUT 180T
"A knocking sound from the machine can be caused by the following reasons and can be resolved as follows:
Transport screws not removed (for new machines)
New machines are shippe...
MTB-CUT M188
Sorry, the cutting machine does not have an app for Android or iOS. The reason is that you need to manually place the cutting material on the machine, and using an app to operate t...
MTB-CUT 180T
This issue usually occurs when the material size settings do not match the template, especially when cutting full back films.
Recommended Solution
When cutting full back film, pl...
MTB-CUT 180T
If the cutting model is in the wrong direction (e.g., mirrored, upside down, or rotated incorrectly), you can adjust it using the mirror and rotation functions:
Use X/Y Axis Mirro...
MTB-CUT 180T
"The intelligent film cutting machine has two belts:
One is used to control the left-right movement of the carriage
https://osscdn.mietubl.com/images/X-axis-belt.jpg
The othe...
MTB-CUT 180T
"If the machine shows an “Insufficient Cutting Times” message, please send your machine username to the dealer who sold you the machine.
They will add more cutting times for your a...
MTB-CUT M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT 180T
"The default cutting speed of the machine is 200. In most cases, keeping the default setting will deliver good cutting performance.
You only need to reduce the speed in special sit...
MTB-CUT 180T
"The machine is equipped with X-axis and Y-axis motors. The X-axis motor is responsible for controlling the horizontal (left-right) movement of the cutting Car.
If the X-axis belt...
MTB-CUT 180T
When the machine beeps with a repeated “bip bip” sound and fails to start cutting, it usually means that the X-axis or Y-axis cannot operate normally.
Common causes include a stuc...
Showing 121
to 140
of 224 results
