Showing 34 results
for
"mainboard fault"
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT 180T
This issue may be caused by:
The material sensor being blocked
A mainboard malfunction
Please try the following steps:
Go to Settings
Disable the “Auto Loading&rdq...
MTB-CUT M188
If your MTB-CUT M188 displays “Time Out” after powering on, it is usually caused by an abnormal serial communication between the screen and the mainboard.
This situati...
MTB-CUT 180T
Sorry, when you say “it stopped working properly”, we need to know the exact fault condition before we can provide the correct solution.
Please:
Record a clear vide...
MTB-CUT 180T
"This can be caused by several issues:
- Incorrect Power Supply: Ensure you are using the original power adapter. An incorrect adapter can cause insufficient power.
- Blade Pressu...
MTB-CUT M288
The “Reconnection” message means that the screen cannot establish a proper connection with the mainboard.
This issue is typically caused by a loose or faulty screen-to...
MTB-CUT 180T
This error is usually caused by a mainboard malfunction.
To fix the issue, please follow these steps:
Replace the mainboard following the instructional video.
Before replacing...
MTB-CUT 180T
If the blade does not drop properly during cutting, this issue is most likely caused by a mainboard malfunction.
The blade-down action is controlled by the Y-axis motor signal fro...
MTB-CUT M188
If your MTB-CUT M188 displays a “Time Out” or “Reconnection” error after startup, please follow the steps below:
Step 1: Check the machine barcode
Check t...
MTB-CUT 180T
"Communication failure with the machine is typically caused by network issues or a mainboard malfunction.
When encountering this problem, please try the following steps:
Reconne...
MTB-CUT 180T
If the machine is vibrating abnormally, please check the following two points:
1. Check the transportation screw
If this is a new machine, please make sure the screw on the back...
MTB-CUT 180T
"If the machine displays a ""Timeout"" error on startup and the ""Reconnect"" button is unresponsive, it usually means the screen cannot properly connect to the mainboard. Possible...
MTB-CUT 180T
"If your device displays the error message “Unable to communicate with the device (13904)”, please navigate to “My” → “About” → “Check if the QR code is displayed”.
If the QR code...
MTB-CUT 180T
"If the Car moves after you initiate cutting, but the blade holder does not drop, this issue may be caused by one of the following reasons:
Insufficient power supply – Please verif...
MTB-CUT M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT 180T
This issue usually occurs after replacing the machine’s mainboard.
Because the machine ID is originally bound to the old mainboard, installing a new mainboard requires the I...
MTB-CUT 180T
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT 180T
When the machine beeps with a repeated “bip bip” sound and fails to start cutting, it usually means that the X-axis or Y-axis cannot operate normally.
Common causes include a stuc...
MTB-CUT M288
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
Showing 1
to 20
of 34 results
