Showing 29 results
for
"mainboard"
MTB-CUT M188
A “Time Out” message usually means that there is a communication failure between the screen and the mainboard. This can be caused by:
Loose or Damaged Screen Cable
Op...
MTB-CUT 180T
"This can be caused by several issues:
- Incorrect Power Supply: Ensure you are using the original power adapter. An incorrect adapter can cause insufficient power.
- Blade Pressu...
MTB-CUT 180T
"This issue can be caused by several reasons:
Low Cutting Pressure
Check your cutting pressure settings.
If the pressure is too low, the blade holder won’t drop enough to tou...
MTB-CUT M288
The “Reconnection” message means that the screen cannot establish a proper connection with the mainboard.
This issue is typically caused by a loose or faulty screen-to...
MTB-CUT 180T
This error is usually caused by a mainboard malfunction.
To fix the issue, please follow these steps:
Replace the mainboard following the instructional video.
Before replacing...
MTB-CUT 180T
If the blade does not drop properly during cutting, this issue is most likely caused by a mainboard malfunction.
The blade-down action is controlled by the Y-axis motor signal fro...
MTB-CUT 180T
"Communication failure with the machine is typically caused by network issues or a mainboard malfunction.
When encountering this problem, please try the following steps:
Reconne...
MTB-CUT 180T
"If the machine displays a ""Timeout"" error on startup and the ""Reconnect"" button is unresponsive, it usually means the screen cannot properly connect to the mainboard. Possible...
MTB-CUT 180T
"If your device displays the error message “Unable to communicate with the device (13904)”, please navigate to “My” → “About” → “Check if the QR code is displayed”.
If the QR code...
MTB-CUT 180T
"If the Car moves after you initiate cutting, but the blade holder does not drop, this issue may be caused by one of the following reasons:
Insufficient power supply – Please verif...
MTB-CUT M288
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT M188
"If the MTB-CUT M288 intelligent film cutting and pasting machine displays a ""Reconnection"" message at startup or if the cutting Car fails to cut properly, the mainboard may be f...
MTB-CUT 180T
This issue usually occurs after replacing the machine’s mainboard.
Because the machine ID is originally bound to the old mainboard, installing a new mainboard requires the I...
MTB-CUT 180T
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT 180T
When the machine beeps with a repeated “bip bip” sound and fails to start cutting, it usually means that the X-axis or Y-axis cannot operate normally.
Common causes include a stuc...
MTB-CUT M288
There are three possible causes for this error:
1. The template width exceeds the maximum supported size
The maximum cutting width of the screen protector machine is 228 mm.
If...
MTB-CUT 180T
If the machine displays a “Time Out” error during film cutting, please follow the steps below:
1. Check whether the motherboard is connected
On the machine, go to:...
MTB-CUT 180T
Error 1002 indicates that a device port is occupied.
In this case, you can try the following steps:
Restart the device and go to "My" → "About This Device" to check if the QR co...
MTB-CUT 180T
"A knocking sound from the machine can be caused by the following reasons and can be resolved as follows:
Transport screws not removed (for new machines)
New machines are shippe...
MTB-CUT 180T
"If your machine stays in the “Status Checking” state for a long time, it may be caused by network delays or communication errors. Please try the following steps:
Restart the machi...
Showing 1
to 20
of 29 results
